Home / Winter supply estimator

Winter supply estimator

Start from official average heating energy for your climate, then adjust for the space you actually heat, the share that comes from wood, the species you burn and how efficient the appliance is.

Your house and climate

Leave the optional heat-need box blank to start from the EIA average for your climate, scaled by your square footage. Enter a number only if you already know your seasonal heat use, for example from a fuel bill converted to million Btu.

Your wood and appliance

Efficiency presets are the worked examples in University of Maryland Extension FS-926: 10% for an open fireplace and 70% for an EPA-approved stove. If your stove lists a different overall efficiency, pick Custom and enter that number. The EPA also notes that a certified stove can use about one third less wood than an older stove for the same heat.

How the estimate is built

For each EIA climate region, the 2020 Residential Energy Consumption Survey reports average site space-heating energy, in million Btu, for households that use space heat (Table CE3.1, revised March 2024): Very cold and Cold, 54; Mixed-humid, 32.6; Mixed-dry and Hot-dry, 15.4; Hot-humid, 11.5; Marine, 23.3.

The same survey reports average heated square footage for all housing units in those regions (Table HC10.9, March 2023): Very cold and Cold, 1,808; Mixed-humid, 1,688; Mixed-dry and Hot-dry, 1,334; Hot-humid, 1,365; Marine, 1,432.

If you leave the optional heat-need box blank, the calculator scales the EIA average household heating energy by the ratio of your heated area to that region's average heated area. That step is a planning assumption, not a per-square-foot number EIA publishes on its own. You can skip it by entering your own seasonal heat need in million Btu.

The wood's share of that heat is whatever you enter. Heat per full cord comes from University of Maryland Extension FS-926, Table 1, for air-dried wood at 20% moisture and 100% unit efficiency. The calculator then multiplies by your appliance efficiency. FS-926's worked examples use 10% for an open fireplace and 70% for an EPA-approved wood stove. Those are labeled examples, not a promise about your unit. If you have a listed overall efficiency, enter it.

Cords = (seasonal heat need x wood share) / (heat per cord x appliance efficiency). A reserve, if you type one, is added after that. This site does not invent a typical reserve.

Worked example

A 1,500 square foot space in the EIA Very cold and Cold region, heated entirely with air-dried red oak (25.3 million Btu per cord in FS-926) in an EPA-approved stove at the 70% example efficiency, has an estimated heat need of 44.80 million Btu (54.0 x 1,500 / 1,808). Each cord delivers 17.71 million Btu, so the estimate is 2.53 full cords, or about 7.6 face cords of 16-inch pieces. The EIA average home in that climate, 1,808 heated square feet, comes to 3.05 cords on the same wood and stove assumptions.

Sources

Common questions

How many cords do I need to heat a house for the winter?

It depends on the climate, the space the wood actually heats, how much of the load the stove carries, the species and the appliance. For the EIA average Very cold and Cold home of 1,808 heated square feet, with red oak and a 70% efficient stove as the only heat, this calculator gives about 3.05 full cords. A milder climate, a smaller space or a furnace that shares the load will need less. An open fireplace, at the 10% example efficiency, will need much more.

What if I only burn wood in the evenings?

Lower the share of heat that comes from wood to match how you actually use the stove, and enter only the floor area the fire keeps warm, not the whole house if the rest is on another system.

Why is my result different from a neighbor's rule of thumb?

Rule-of-thumb cord counts often skip climate, house size, species and stove efficiency, or they bake in a reserve. This page shows each of those pieces and lets you change them. If you already know last winter's use, that measured number is better than any estimate.

Estimates only. These tools are for planning, not quotes and not legal or financial advice. A full cord is 128 cubic feet of ranked and well stowed wood under NIST Handbook 130. In states that adopted that rule, firewood is sold by the cord or a fraction of a cord, not by the face cord, rick, pile or truckload. Confirm your measurements and local rules with the seller and your state weights and measures office.

By James Johnston. Updated November 2026. Estimates for planning, not advice. See sources and method.